Proposal of a novel design for linear superconducting motor using 2G tape stacks

This paper presents a new design for a su- perconducting linear motor (SLM). This SLM uses stacks of second-generation (2G) superconducting tapes, which are responsible for replacing yttrium barium copper oxide bulks. The proposed SLM may operate as a synchronous motor or as a hysteresis motor, depending on the load force magnitude. A small-scale linear machine prototype with 2G stacks was constructed and tested to investigate the proposed SLM topology. The stator traveling magnetic field wave was represented by several Nd-Fe-B permanent magnets. A relative movement was produced between the stator and the stack, and the force was measured along the displacement. This system was also simulated by the finite element method, in order to calculate the induced currents in the stack and determine the electromagnetic force. The H-formulation was used to solve the problem, and a power law relation was applied to take into account the intrin- sically nonlinearity of the superconductor. The simulated and measured results were in accordance. Simulated re- sults were extrapolated, proving to be an interesting tool to scale up the motor in future projects. The proposed motor presented an estimated force density of almost 500 N/kg, which is much higher than any linear motor.This work was supported in part by the following agencies: CNPq/CAPES/INERGE, CNPq—Ci ˆ encias sem Fronteiras, FAPERJ, Catalan Government 2014- SGR-753, CONSOLIDER Excellence Network MAT2014-56063-C2-1-R and MAT2015-68994-REDC, Eurofusion EU COST ACTIONS MP1201/ MP1014/PPPT-WPMAG 2014, EUROTAPES FP7-NMP-Large-2011- 280432, FORTISSIMO FP7-2013-ICT-609029, and Spanish Govern- ment Agencies—Severo Ochoa Programme Centres of Excellence in R&D. (Corresponding author: Guilherme G. Sotelo.

Fundamentals, topologies and optimization methods of saturated iron core fault current limiter

The energy transition is a necessity to satisfy the consumption and impact of humanity on the environment. Therefore, to fulfill this demand, renewable energies and microgrids have been developed. Consequently, fault current levels have overcome the circuit breaker capacity in many substations over the years. Then, the development of the fault current limiters has become a potential solution to solve this problem. The literature has presented several topologies over the past decades. The saturated iron-core fault current limiter (SIC-SFCL) has exhibited promising results since this topology is tested in the distribution and transmission system substation. Thus, enforcements to increase the maturity of this equipment have been developed in different areas, for example, design, applied superconductor materials, and optimization models of the SIC-SFCL. This article has presented the fundamental concept of this equipment. Beyond that, the principal topologies have been discussed. The article has delivered further information about the main parts that comprise this equipment. Also, the authors have introduced different characteristics which affect the recovery times of this device. The authors have discussed the optimization methods applied to this equipment and after the conclusion is presented

Optimization of the Superconducting Linear Magnetic Bearing of a Maglev Vehicle

Considering the need for cost/performance prediction and optimization of superconducting maglev vehicles, we develop and validate here a 3D finite element model to simulate superconducting linear magnetic bearings. Then we reduce the 3D model to a 2D model in order to decrease the computing time. This allows us to perform in a reasonable time a stochastic optimization considering the superconductor properties and the vehicle operation. We look for the permanent magnet guideway geometry that minimizes the cost and maximizes the lateral force during a displacement sequence, with a constraint on the minimum levitation force. The displacement sequence reproduces a regular maglev vehicle operation with both vertical and lateral movements. For the sake of comparison, our reference is the SupraTrans prototype bearing. The results of the optimization suggest that the bearing cost could be substantially reduced, while keeping the same performances as the initial design. Alternatively, the performances could be significantly improved for the same original cost

2D Modeling of HTS Coils with T-A Formulation: How to Handle Different Coupling Scenarios

Numerical models based on the finite-element method (FEM) are popular tools for investigating the macroscopic electromagnetic behavior of high-temperature superconductor (HTS) applications. This article explains how to use the T-A formulation for modeling HTS coils in 2D with different coupling scenarios between the turns. First we consider a racetrack coil wound from one piece of superconducting tape. Then we consider a coil obtained by winding a cable composed of different HTS tapes. In the latter case, the tape turns are either electrically connected along their entire length or just at the two ends of the coil: in the model, these two different types of electrical connection are implemented with the help of the electrical circuit module. The current density distributions and the AC losses of the coils in the different coupling scenarios are compared and discussed. The limits of applicability of the presented approach are pointed out. The model is developed for the straight section of racetrack coils, but can be easily adapted to axisymmetric geometries

Magnetic bearings with double crossed loops modelled with T-A formulation and electric circuits

The application of High-Temperature Superconductor (HTS) coils made of coated conductors has been investigated for many years. A possible configuration for such coils is the jointless loop, also known as the ring coil. The double crossed loop coil (DCLC) has been successfully applied in superconducting magnetic bearings (SMBs). The design of SMBs with DCLCs requires flexible modelling to allow all parts of the device to be represented. This work proposes the T-A formulation with a thin-film approximation for modelling SMB with DCLCs in the finite element analysis framework. A 2D representation of the system is coupled with an external electric circuit to model the continuity of the lines that represent the parts of each jointless loop. To couple the T-A formulation and the circuit, an average of the total electric field, with both resistive and inductive components, is applied to the circuit. The total current computed by the circuit is applied to the T-A formulation. The proposed methodology was validated by comparison with levitation force experimental data. Two types of tests were simulated: five levitation force tests and three guidance force tests. It is shown that there is a limit to the behaviour of the levitation force related to the high-loss state. Below this limit, the stack of DCLCs behaves as an equivalent bulk. Beyond this limit, a high-loss state appears as a linear growth of the levitation force. It is also shown that this high-loss state in vertical displacement influences the lateral force

Oregano essential oil and its main components Thymol and Carvacrol as alternatives to control citrus canker

Plant Essential Oils and their constituents are well-known for their properties as antimicrobial agents and are labeled as Generally Recognized as Safe (GRAS), prompting studies around their usage in the control of food-borne microorganisms and phytopathogens. In this study, we evaluated Oregano Essential Oil (OEO), Thymol (THY) and Carvacrol (CAR) for the control of Xanthomonas citri subsp. citri (X. citri). In vitro antibacterial assays revealed that CAR and THY inhibit X. citri growth at the concentrations of 100 µg.mL-1 and 114 µg.mL-1, lower than OEO (136 µg.mL-1). Bactericidal effects were observed at 400 µg.mL-1 for OEO and 200 ug.mL-1 for CAR and THY. Investigating potential cellular targets for the compounds showed that after 30 minutes of exposure up to 84% of the cells had their membranes disrupted, implicating the membrane as the primary target. Phytotoxicity evaluations using Lactuca sativa and Solanum lycopersicum seeds showed an acute toxic effect in all treatments above 200 µg.mL-1, except for OEO and THY in S. lycopersicum at lower concentrations. Regarding their protective effect on citrus leaves, CAR showed no effect when compared to the untreated control (0.39 and 0.50 lesions per cm2, respectively). OEO and THY were able to reduce significantly citrus canker symptoms (0.18 and 0.11 lesions per cm2, respectively). In addition, no toxic effects were observed on citrus leaves in all treatments. THY inhibits X. citri growth and the development of citrus canker lesions. These results show that THY as a viable alternative to be used in citrus canker management

Development of a clinical laboratory data baseof hyper and hypo alpha lipoproteins in Campinas-SP and neighboring region

ABStrACt Introduction: The development of research for diagnosis, prevention and treatment of atherosclerotic cardiovascular disease is of utmost importance due to the fact that it is the main cause of morbidity and mortality in Brazil. Objective: To demonstrate the phases of the selection process for candidates with the aim to develop a clinical-laboratorial database of hyper alpha lipoproteinemic patients (hyper A) -high density lipoprotein cholesterol (HDL-C) ≥ 68 mg/dl) and hypo alpha lipoproteinemic patients (hypo A) -HDL-C ≤ 39 mg/dl. Material and methods: The volunteers were contacted after selection of lipid profiles from individuals treated at the Sistema Único de Saúde (SUS), Campinas-SP and neighboring area. Afterwards, the selected patients went through blood collection, clinical examinations and answered questionnaires on dietary frequency and physical activity. After this preliminary evaluation, some individuals were convened to another blood collection and, subsequently, were submitted to an ultrasonographic exam of the carotid arteries. Results: Only 0.6% and 0.3% from 598,288 lipid profiles were selected for hyper A and hypo A groups, respectively, including gender disparity. Lack of effective questionnaires (75%), missing calls (60%) and non-inclusion were the major hindrances in the construction of this database. Discussion: The difficulties to obtain eligible candidates were also due to the low prevalence of both groups hypo A and hyper A and the high prevalence of pathologies that contribute to non-genetic variations of HDL-C. Conclusion: In spite of the obstacles in the development of this database, this study brought about several scientific publications. Furthermore, the development of molecular analyzes and functionality will shortly generate other findings, contributing to the diagnosis and follow-up of HDL dyslipidemias

Guidelines for the use and interpretation of assays for monitoring autophagy (3rd edition)

In 2008 we published the first set of guidelines for standardizing research in autophagy. Since then, research on this topic has continued to accelerate, and many new scientists have entered the field. Our knowledge base and relevant new technologies have also been expanding. Accordingly, it is important to update these guidelines for monitoring autophagy in different organisms. Various reviews have described the range of assays that have been used for this purpose. Nevertheless, there continues to be confusion regarding acceptable methods to measure autophagy, especially in multicellular eukaryotes. For example, a key point that needs to be emphasized is that there is a difference between measurements that monitor the numbers or volume of autophagic elements (e.g., autophagosomes or autolysosomes) at any stage of the autophagic process versus those that measure fl ux through the autophagy pathway (i.e., the complete process including the amount and rate of cargo sequestered and degraded). In particular, a block in macroautophagy that results in autophagosome accumulation must be differentiated from stimuli that increase autophagic activity, defi ned as increased autophagy induction coupled with increased delivery to, and degradation within, lysosomes (inmost higher eukaryotes and some protists such as Dictyostelium ) or the vacuole (in plants and fungi). In other words, it is especially important that investigators new to the fi eld understand that the appearance of more autophagosomes does not necessarily equate with more autophagy. In fact, in many cases, autophagosomes accumulate because of a block in trafficking to lysosomes without a concomitant change in autophagosome biogenesis, whereas an increase in autolysosomes may reflect a reduction in degradative activity. It is worth emphasizing here that lysosomal digestion is a stage of autophagy and evaluating its competence is a crucial part of the evaluation of autophagic flux, or complete autophagy. Here, we present a set of guidelines for the selection and interpretation of methods for use by investigators who aim to examine macroautophagy and related processes, as well as for reviewers who need to provide realistic and reasonable critiques of papers that are focused on these processes. These guidelines are not meant to be a formulaic set of rules, because the appropriate assays depend in part on the question being asked and the system being used. In addition, we emphasize that no individual assay is guaranteed to be the most appropriate one in every situation, and we strongly recommend the use of multiple assays to monitor autophagy. Along these lines, because of the potential for pleiotropic effects due to blocking autophagy through genetic manipulation it is imperative to delete or knock down more than one autophagy-related gene. In addition, some individual Atg proteins, or groups of proteins, are involved in other cellular pathways so not all Atg proteins can be used as a specific marker for an autophagic process. In these guidelines, we consider these various methods of assessing autophagy and what information can, or cannot, be obtained from them. Finally, by discussing the merits and limits of particular autophagy assays, we hope to encourage technical innovation in the field

Modelling of Two Topologies of Trapped-flux Machines with Second Generation Tapes Using T-A 3D Formulation

International audienceThis work presents modelling and magneti- zation comparison of two topologies of partially super- conducting trapped-flux machines with second generation tapes, one with spiral stacks and other with layers of sheets with holes. Modelling is done with finite element method and the T-A formulation in 3D. From results, it is found that the second topology has stronger magnetization